Skip to content

Made in Gdańsk

ALUSTEER guided pipe jacking - slurry-free pipe jacking machine

ALUSTEER is a Polish slurry-free machine for guided pipe jacking: it installs pipes under roads, railway tracks or pavements without digging up the surface. It handles bores up to 70 m and Ø 30-250 mm, weighs 105 kg, is radio remote-controlled and also handles pipe bursting. We build it in Gdańsk and sell it across Europe.

ALUSTEER pipe jacking machine with pilot head
Bore lengthup to 70 m
Installation diametersØ 30-250 mm
Pullback force32 t
Machine weight105 kg
  • Water & sewer
  • Telecoms
  • Power
  • Gas
  • Roads
  • Pipe bursting

Technology

How guided pipe jacking works

Guided pipe jacking is a trenchless technology: it lets you lay pipes and cables underground without digging up the surface. A hydraulically driven machine pushes a pilot head into the ground, which the operator steers and corrects on the go to avoid obstacles. Once it reaches the reception pit, a reaming head pulls in the product pipe.

Guided pipe jacking diagramGround cross-section with the launch pit on the left and the reception pit on the right. The machine in the launch pit pushes the pilot head under the road, a locator on the surface tracks its position, and in the reception pit the pipe is pulled into the bore.road, tracks, watercourselaunch pitreception pit123456
Illustrative diagram, not to scale. Select a step to see where it takes place.
  1. Two pits are dug: a launch pit and a reception pit. The operator sets the bore path based on the survey documentation and ground conditions.

  2. The pipe jacking machine is aligned with the planned crossing, ready to start the pilot bore.

  3. The pilot head is pushed into the ground while the operator continuously monitors and corrects its direction, pitch and depth.

  4. Measuring systems track the head position in real time, keeping high precision along the entire length of the bore.

  5. Once the reception pit is reached, the pilot head is replaced with a reaming head with a pipe puller. As the drill rods are withdrawn, the bore is enlarged and filled with the product pipe.

  6. The route accuracy and tightness of the installation are checked, then both pits are backfilled and the site is restored to its original condition.

Prepared by
  • Marek FijałoMarek Fijało
    co-owner and designer of ALUSTEER · LinkedIn
  • Cyprian FijałoCyprian Fijało
    co-owner and designer of ALUSTEER · LinkedIn
Guided pipe jacking, HDD or mole - a comparison

Applications

Where guided pipe jacking works best

ALUSTEER guided pipe jacking installs pipes and cables from 30 to 250 mm in diameter over runs of up to 70 m under obstacles that cannot be dug up, or are not worth digging up. It works without bentonite drilling fluid, so no spoil is left on site to haul away.

Street cross-section with a carriageway, pavement and cycle path. Existing pipes run beneath the surface, and a guided bore is driven from a pit with the ALUSTEER machine.
  1. 1

    Surface navigation

    The receiver tracks the pilot head, so the operator knows its depth and direction along the whole route.

  2. 2

    Pavements and car parks

    Paving and kerbs above the route stay in place, with no cost of relaying them.

  3. 3

    Roads and streets

    The pipe passes under the carriageway and crossing while traffic above the bore keeps moving.

  4. 4

    Cycle paths

    The cycle path stays open, as there is no trench above the route.

  5. 5

    Existing underground utilities

    The steerable head avoids pipes and cables already in the ground.

  6. 6

    Pit with the ALUSTEER machine

    The machine sits in the launch pit, clear of the carriageway and the cycle path.

Also: crossings under railway tracks and service connections to properties.

Installations
  • Water and sewer
  • Gas
  • Fibre optics and telecoms
  • Power
Pipe bursting: replacing an old pipe along the same route

ALUSTEER system components

The machine, navigation and tooling form a complete kit for guided pipe jacking, from the launch pit to the reception pit.

ALUSTEER machine

Fully equipped guided pipe jacking
Render of the ALUSTEER machine
ALUSTEER set up between thrust plates

Main hydraulic module with pilot head - delivers 27 t of thrust and 32 t of pullback force.

Handles installation diameters up to Ø 250 mm.

ALUSTEER machine - technical data

Method comparison

Guided pipe jacking, HDD or mole - which method to choose?

Choose ALUSTEER guided pipe jacking for crossings up to 70 m where path control and slurry-free work matter. HDD is for long crossings measured in hundreds of metres, and a pneumatic piercing tool for short, straight runs that need no steering.

Comparison of ALUSTEER guided pipe jacking, HDD and a pneumatic piercing tool
ParameterALUSTEER guided pipe jackingHDDPneumatic piercing tool
Path steeringYes, the operator corrects direction, pitch and depth on the goYes, curved path with correction in three axesNo, the mole moves without path control
Typical lengthup to 70 mfrom several dozen to over 2000 mshort, straight runs
Installation diameterØ 30-250 mmup to approx. 2 msmaller pipe diameters
Mobilisation costlower than HDDhigherlow
When to chooseCrossings under roads, tracks and pavements, service connections, gravity sewersLong crossings under rivers and national roads, pressure pipelinesA short run in easy terrain where precision is not critical

Matching the head to the ground

Matching the head to the ground
HeadGround and performance
Sharp cone headSoft and wet soils and sands. Gives greater sensitivity and faster response to steering.
Blunt cone headHarder soils and clays, where high steering sensitivity is not needed.

Guided pipe jacking vs HDD - when to choose which methodHydraulic guided pipe jacking or a mole

Data sheet

ALUSTEER technical specification

The ALUSTEER machine weighs 105 kg, pushes with 27 t and pulls with 32 t, and performs guided pipe jacking over up to 70 m for Ø 30-250 mm installations. It is powered by the HAS 300-20 power unit at 300 bar or by excavator hydraulics.

Technical data of the ALUSTEER machine and the HAS 300-20 power unit
Guided pipe jacking
Bore lengthup to 70 m
Installation diameterØ 30-250 mm
Thrust force27 t
Pullback force32 t
Max. operating pressure300 bar
Weight105 kg
Dimensions734 × 500 × 312 mm
Constructionaluminium
Controlradio remote control
Bentonite drilling fluidnot needed
Pipe bursting
Bursting diameterØ 80-160 mm
Max. bursting length40 m
HAS 300-20 hydraulic power unit
EngineLONCIN petrol 18 kW (27 HP)
Startingelectric
Pressure300 bar
Flow rate0-20 l/min, steplessly adjustable
Fuel tank25 l
Hydraulic oil tank25 l
Cooler airflow2100 m³/h
Net / gross weight110 / 150 kg
Dimensions800 × 1200 × 800 mm

Videos

ALUSTEER at work

Short videos from job sites and from production in Gdańsk. They show ALUSTEER guided pipe jacking in real conditions: under a road, under a gas pipe and in stony ground.

Machine and purchase terms

Why ALUSTEER

ALUSTEER is an aluminium guided pipe jacking machine that weighs 105 kg and works without drilling fluid. You buy it directly from the manufacturer in Gdańsk, with free delivery, free operator training, a manufacturer's warranty and help with leasing.

ALUSTEER machine set up in the launch pit between thrust plates
Made in Gdańsk

Machine

  • 105 kg

    Aluminium construction

    You can transport the machine without a crane and carry it into the launch pit.

  • slurry-free

    Works without bentonite

    You need no bentonite or water, and no spoil is left on site to haul away.

  • remote

    Radio control

    The operator corrects the head's direction with a remote control, with no cables.

  • 27 / 32 t

    Power in a compact size

    27 t of thrust and 32 t of pullback from a machine measuring 734 × 500 × 312 mm.

You buy directly from the manufacturer

  • Manufacturer in Gdańsk
    We design and build the machines in Gdańsk, and you buy them directly from us.
  • Free delivery
    The machine is delivered to the customer at no extra cost.
  • Free training
    Operator training on the machine at no extra cost.
  • Manufacturer's warranty
    The warranty is provided by the manufacturer.
  • Service and parts
    Service and spare parts straight from the manufacturer.
  • Help with leasing
    We help you get in touch with a leasing company and prepare the application.

You can test the machine at the pipe jacking centre in Gdańsk.

Request a quote

FAQ

Frequently asked questions about guided pipe jacking

10 questions contractors ask before buying the machine.

Your question isn't here?
Give us a call - the machine's designer will answer.

+48 534 979 628
01What is guided pipe jacking?

It is a trenchless method of laying pipes and cables underground. A hydraulic machine pushes a pilot head into the ground, which the operator steers and corrects, and once it reaches the reception pit, it pulls in the product pipe.

02Does ALUSTEER need bentonite?

No. ALUSTEER works without bentonite drilling fluid and without water, because the ground is displaced and compacted rather than flushed out. No spoil is left on site to haul away.

03What is the maximum bore length and diameter?

With the ALUSTEER machine you can bore up to 70 m for installations of Ø 30-250 mm. For pipe bursting, the range is Ø 80-160 mm over up to 40 m.

04What ground is suitable for guided pipe jacking?

For soft and wet soils and sands, a sharp cone head is used, as it responds faster to steering. For harder soils and clays, a blunt cone head is enough.

05How accurately is the head guided?

A sonde in the head sends a signal to the receiver on the surface, and the operator sees depth, pitch and direction on a tablet.

06Can you bore under a road or railway tracks?

Yes. The launch and reception pits sit on either side of the obstacle, and the 70 m range lets you pass under the carriageway together with the verges. Boring under a road or tracks requires approval from the authority that manages it.

07How does ALUSTEER differ from HDD?

ALUSTEER works without drilling fluid and without spoil, and the machine weighs 105 kg. HDD is used for long crossings measured in hundreds of metres and requires a drilling rig, a drilling fluid system and space to lay out the pipe.

08How much does the machine weigh, and is a crane needed?

The ALUSTEER machine has an aluminium construction and weighs 105 kg, so no crane is needed. The HAS 300-20 power unit weighs 110 kg net.

09How long does a 30 m bore take?

A 30 m guided bore takes about 30 minutes.

10Does ALUSTEER work in winter and with a high water table?

Yes. ALUSTEER works without problems in winter and with a high water table.

Ask about the ALUSTEER machine

Tell us what kind of bores you do. We'll reply with a suggested kit and purchase terms.

Address
Jana Kochanowskiego 130
80-405 Gdańsk
Hours
9:00-18:00
What is your enquiry about
The machine's designer will reply within 48 hours.
FIJALO-POLAND

ALUSTEER® is a brand of FIJALO-POLAND, a manufacturer of machines for work on underground utilities. All brands on fijalo.pl