Skip to content

ALUSTEER machine application

Pipe bursting - trenchless pipeline replacement

Pipe bursting is the trenchless replacement of an old pipeline. The bursting head breaks up the old pipe from the inside, and the new pipe of the same or larger diameter follows right behind it. With the ALUSTEER machine you can burst pipes of Ø 80-160 mm over lengths of up to 40 m, from the same launch pit.

Bursting diameterØ 80-160 mm
Max. length40 m

The same machine as for guided pipe jacking, powered by a power unit or excavator hydraulics.

How pipe bursting works

The old pipe sets the route. The head follows it, and the new pipe goes in right behind.

Pipe bursting diagramCross-section of the ground with the launch pit on the left and a second pit on the right. The old pipe runs below the surface. The bursting head breaks it up halfway along the route, and the new pipe enters the ground behind the head.surface left untouchedlaunch pitsecond pitold pipenew pipe123
Illustrative diagram, not to scale. Pipe bursting runs the same way as guided pipe jacking.
  1. 1

    Launch pit

    The ALUSTEER machine is set up in the launch pit, without digging up the route of the old pipe.

  2. 2

    Bursting head in the old pipe

    The head passes through the old pipe and breaks up its walls from the inside.

  3. 3

    New pipe behind the head

    The new service pipe takes the place of the old one, along the same route.

Pipe bursting or a new guided pipe jacking bore

Pipe bursting works where an existing pipeline needs replacing and the route is already set. There is no need for a new bore alongside the old line, because the new pipe uses the existing service corridor.

If there is no pipe yet, or the route needs to run differently, choose guided pipe jacking: up to 70 m, for Ø 30-250 mm utilities.

Pipe bursting vs ALUSTEER guided pipe jacking
ParameterPipe burstingGuided pipe jacking
Purposereplacing an old pipe with a new one along the same routenew utility under an obstacle, along a new route
DiameterØ 80-160 mmØ 30-250 mm
Max. length40 m70 m
Routeroute of the old pipeany, corrected on the fly
Old pipebroken up, replaced by the new onestays next to the new utility
MachineALUSTEERALUSTEER

Pipe bursting parameters with the ALUSTEER machine

The pipe bursting tooling, including special cutting heads, is an accessory ordered separately.

Pipe bursting parameters with the ALUSTEER machine
Bursting diameterØ 80-160 mm
Max. bursting length40 m
New pipe diametersame as or larger than the old one
Max. new pipe diameterØ 160 mm
Old pipe materialsHDPE, PE, PVC, concrete, vitrified clay, cast steel, cast iron
Power supplyHAS 300-20 power unit or excavator hydraulics, 300 bar and 20 l/min

Pipe bursting questions

01How does pipe bursting work?

The bursting head breaks up the old pipe from the inside, and the new pipe follows right behind it. The work is done from pits, without digging up the route.

02Which pipes can be burst with the ALUSTEER machine?

Pipes of Ø 80-160 mm over lengths of up to 40 m. Materials: HDPE, PE, PVC, concrete, vitrified clay, cast steel and cast iron. Not every diameter and not every material can be cut, though.

03Can the new pipe be larger than the old one?

Yes, the new pipe can have the same or a larger diameter, up to Ø 160 mm. One of our customers has even burst up to Ø 315 mm.

04Is a separate machine needed for pipe bursting?

No. Pipe bursting is done by the same ALUSTEER machine that performs guided pipe jacking. You need the pipe bursting tooling with special cutting heads, ordered separately.

05What are the limitations of pipe bursting?

Not every diameter and not every material can be cut. The new pipe can be up to Ø 160 mm. Tell us the material, diameter and length of the section, and our design engineer will check whether pipe bursting is the right choice.

Prepared by
  • Marek FijałoMarek Fijało
    co-owner and designer of ALUSTEER · LinkedIn
  • Cyprian FijałoCyprian Fijało
    co-owner and designer of ALUSTEER · LinkedIn

Ask about the ALUSTEER machine

Got a pipe to replace? Give us the material, diameter and length of the section and our design engineer will check whether pipe bursting will work. You can test the machine at our pipe jacking centre in Gdańsk.

The whole system in one place

How guided pipe jacking works, machine data, comparison with HDD and the impact mole.

ALUSTEER guided pipe jacking - how it works and machine data
FIJALO-POLAND

ALUSTEER® is a brand of FIJALO-POLAND, a manufacturer of machines for work on underground utilities. All brands on fijalo.pl